User Manual

When Lullabee detects your child is awake and crying, it helps soothe with gentle vibration and calming sound. The support increases the longer your child is awake. Once asleep, Lullabee slowly decreases the support and then tapers off completely.

Phases:

Phase 1 (Support Phase): Lullabee increases the level of soothing rhythms as needed. As your child grows and begins falling asleep quickly and easily, Lullabee automatically transitions to Phase 2.

Phase 2 (Wean Phase): Lullabee gradually decreases the support level over several days to weeks. If your child’s sleep worsens, it automatically goes back to Phase 1. There is no guesswork for parents – Lullabee handles everything automatically.

Lullabee requires no input from the caregiver.

Who Should Use it?

Lullabee is designed to meet standard crib mattress safety specifications and is safe to use as early as the newborn phase. Please check your crib manufacturer’s safety specifications for height and weight requirements.

Who Shouldn’t Use it?

Children with medical conditions that cause sensitivity to vibrations or sounds should not use Lullabee. Consult your child's physician if you have any concerns.

Please see our FAQ section for more information.

Quick Start Guide

Step 1: Unzip the outer cover along the front panel to access the inner cover and battery compartment.

Step 2: Locate the opening in the inner cover. Separate the cloth to reveal the battery compartment and insert the battery.

Step 3: Ensure the inner cover is put back in place to fully cover the battery compartment.

Step 4: Close the zipper of the outer cover. Apply a crib sheet if desired.

Step 5: Place Lullabee in crib and press the large middle button to turn it on. You’re all set!

User Interface

Lullabee has three buttons along the front panel.

To power on: Briefly press Power button

To power off: Press and hold Power button for 3 seconds

⚠️ Safety Feature: For your child’s protection, Lullabee will automatically power off if crying is detected for more than 5 minutes while the device is providing maximum soothing.

The following changes can only occur when Lullabee is in “awake” mode. Simply tap on the mattress or briefly press the power button to awaken Lullabee.

To change the vibration pattern: Briefly press the Vibration button. A small sample of the vibration pattern will play. There are 6 options:

Gentle Rumble: Constant vibration, lower overall intensity
Busy Buzz: Constant vibration, medium intensity
Queen Bee: Constant vibration, higher overall intensity
Rolling Hills: Gentle ups and downs in vibration intensity
Heartbeat: Mimics the pulsation of a heartbeat
Off: A tone will play when selected

To change the audio pattern: Briefly press the Audio button. A small sample of the audio selection will play. There are 6 options:

White Noise
Ocean Waves
Spring Rain
Gentle Piano Lullaby
Dream Journey Lullaby
Off: a tone will play when selected

To increase mattress sensitivity (i.e. make it more likely to turn on with less movement and less crying): Press the Vibration button for more than 5 seconds. You will hear a chime. A low tone indicates you’ve already reached max sensitivity.

To decrease sensitivity (i.e. make it less likely to turn on with movement and crying): Press the Audio button for more than 5 seconds. You will hear a chime. A low tone indicates you’ve already reached the lowest sensitivity.

To put Lullabee into Bluetooth Pairing mode: Follow instructions within the app.

Warning lights (only displays for a few seconds after the power button is pressed):

Solid orange: Battery is low

Fast orange flashing: System error.
Power off the device, remove battery, re-insert battery, and power on Lullabee.
If error persists, click here for Customer Support

The Lullabee App

For expanded capabilities and additional features, please download the Lullabee app.

iOS App

Android App

Caring for Lullabee

Washing Lullabee:

Outer cover: Lullabee’s outer cover is waterproof and can be removed for washing. Please wash in cold water on a gentle cycle and allow it to air dry.
Inner cover: The inner cover is a mandatory fire retardant and should never be removed. Removing the inner cover is a safety hazard and voids Lullabee’s warranty.

Storage:

When not in use, store Lullabee in a temperature-controlled environment. Avoid exposure to water or excessive heat. Remove the battery while in storage and store it separately.

Battery

Battery Life:

Lullabee comes with a pre-charged battery that lasts around three weeks, or longer if Lullabee is powered off when not in use. If the battery life falls below 15%, the power button will briefly display a solid orange light when first turned on or pressed. This light will not turn on spontaneously to avoid waking your sleeping child. The app will also alert you when the battery life is below 15%, but you must open the app to receive this notification. This prevents unwanted alerts from waking you during the night. Extra batteries can be purchased through Lullabee.com.

Usage:

Lullabee can remain powered on continuously. It will automatically enter a deep sleep mode to conserve battery life and will awaken when your child moves or when the middle power button is pressed. For maximum battery life, turn off Lullabee by pressing and holding the power button for more than 3 seconds when not in use.

Charging:

Only use the supplied charger to recharge the battery. LED lights on the battery indicate the level of charge, and it takes approximately 4 hours to reach a full charge. The final light will stop blinking when the battery is fully charged.

Disposal:

Dispose of old batteries promptly and in accordance with local laws and regulations.Warning:

Do not touch contacts together.
Do not demolish or open battery.
Do not put the battery in a damp place, dispose of in fire, or short circuit. May ignite, explode, leak, or get hot causing injury.

Caution:

Risk of fire and burns. Do not open, crush, heat above 60 degrees Celsius or incinerate.
Follow the manufacturer’s instructions.

Specifications:

LiFePO4 (lithium-iron) rechargeable battery pack:
9.6V nominal, 1800mAh, 400mA output
Charging Power Supply:
AC 100-240VAC 50/60Hz
USB A 5VDC – 2.4A (12Watt)
UL Listed E340226

Safety Information

Please abide by the American Academy of Pediatrics Safe Sleep Recommendations.

warning WARNING

SIDS AND SUFFOCATION HAZARDS

Failure to follow these warnings and the instructions could result in serious injury or death.

WARNINGS:

ALWAYS place baby on back to sleep to reduce the risks of SIDS and suffocation.
Babies have suffocated on pillows, comforters, and extra padding.
Babies have suffocated in gaps between a wrong-size mattress, or extra padding, and side walls of product.
NEVER add soft bedding, padding or an extra mattress.
This mattress is intended to be used WITHOUT A FOUNDATION.
USE ONLY one mattress at a time.
DO NOT cover the faces or heads of babies with a blanket or over-bundle them. Overheating can increase the risk of SIDS.
ALWAYS check mattress fit every time you change the sheets, by pushing mattress tight to one corner. Look for any gaps between the mattress and the side walls. If a gap is larger than 1 1/2 in. (3.8 cm), the mattress does not fit – do not use it.
DO NOT use this mattress in a crib having interior dimensions that exceed 28 5/8 by 53 in. (73 by 135 cm) as measured from the innermost surfaces of the crib.
USE ONLY sheets and mattress pads designed specifically for crib mattresses.

PREVENT INJURIES

Never place more than one child on Lullabee at a time.
Never use Lullabee outside of a standard crib.
Lullabee should only be used inside a CPSC-certified standard crib.
Only use batteries supplied by Lullabee.
Never use Lullabee if parts are missing or broken.
Only use Lullabee indoors.
Do not allow children to play with Lullabee or change settings.
Do not pour water or liquids onto Lullabee.
Use only the power adapter provided by Lullabee to charge the battery.

COMPLIANCE NOTICE
Contains Transmitter Module FCC ID: WAP6045

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.